When the printer is used for a long time, the actual ink volume of the waste ink pad is larger than the data monitored by the printer, causing the printer to be damaged, or the quality of the print is uneven, such as discoloration, disconnection, and bifurcation during the print of the artwork. Are these troublesome issues tricky? In fact, these problems have a direct relationship with the ink cartridges, and as long as you recognize some misuses, these situations will be greatly improved.

Misunderstanding 1: The ink cartridge can add ink without limit

Many people think that the ink cartridge is just a container filled with ink. As long as the surface of the ink cartridge is not broken, ink can be added continuously. In fact, this is another big mistake.

First of all, the sponge in the ink cartridge has a certain life span. When the sponge repeatedly repeats the process of “absorbing & releasing” the ink or using it for more than a certain period of time, the ink absorption capacity of the sponge will be reduced, thus filling The ink that enters the ink cartridge will not be completely absorbed by the sponge, and the pressure of the ink in the ink cartridge on the nozzle portion will increase, causing the ink to flow from the nozzle. This is one reason why many people complain that the amount of ink to be refilled is not as good as the original ink. Even more serious is that the printer cannot monitor this part of the ink flowing to the waste ink pad. Therefore, the actual waste ink amount of the waste ink pad may be much larger than the amount of waste ink detected by the printer, so that when the printer has not issued a waste ink overcapacity alarm Waste ink has overflowed, causing damage to the printer.

Secondly, between the ink cartridge and the ink inlet of the nozzle, a rubber seal is used to ensure the seal between the ink cartridge and the nozzle to ensure that the ink cannot seep out. Long-term use or multiple removal of the ink cartridge will cause the seal ring to age, and the sealing effect will deteriorate, causing the ink to seep from the joint. This will cause the ink to accumulate and mix on the spray head, resulting in the color mixing of the bottom ink. The direct result is printing. When the artwork is discolored, the colors will need to be printed before the artwork returns to normal. This situation can also lead to waste of ink and an increase in the amount of printer waste ink.

Thirdly, no matter how much ink is filled, some impurities or dust are carried into the interior of the ink cartridge after multiple filling. The dust will be carried to and adsorbed on the filter mesh of the ink cartridge when the ink flows. As the dust increases, the ink cartridge filter will be blocked, resulting in poor ink flow, resulting in problems such as disconnection during printing. If the filter is completely clogged, failures such as being unable to print may occur. Therefore, when the ink is filled more than ten times or one ink cartridge is used for more than one year, it is better to consider replacing the new ink cartridge to avoid various problems.

Misunderstanding 2: The printer waste ink is oversized and can be cleared by the program.

Recently, the issue of overcapacity of waste ink before the printer's ink filling has been discussed in various forums is also very enthusiastic. Many of my friends believe that after the waste ink exceeds the capacity, only the printer maintenance program needs to be run to clear the printer's waste ink counter.

In fact, the waste ink of the maintenance program only clears the waste ink counter in the printer, and the waste ink generated by the printer due to nozzle cleaning, power-on self-test, etc. still exists. If we simply reset the waste ink counter without cleaning the printer's waste ink pad, the waste ink in the waste ink pad will continue to increase as the printer continues to work. Once the printer's waste ink pad is full of waste ink, waste ink can flow out.

If these waste inks flow to the printer's power board or control board, it will cause a short circuit in the board, causing damage to the printer. Even if the waste ink does not overflow, when the printer wastes ink, the vapor evaporated from the waste ink pad will also damage the printer's circuit board, action mechanism, and even the print head.

Of course, some friends think that when the printer waste ink exceeds the warning, the waste ink in the waste ink pad is not full, and there is no need to clean the waste ink pad. Indeed, in many places (especially in southern China's high-temperature areas), printers waste ink, there is not much ink on the waste ink pad, and the printer alarm has a certain margin, so it gives many friends the impression of “no danger”. However, we cannot use this as a reason for not needing to clean up the waste ink pad because the amount of waste ink on the waste ink pad has many variables, such as the temperature level, the humidity level of the air, whether the printer leaks ink, etc., and even if Waste ink does not overflow when a waste ink alarm occurs. Then the second and third alarms!

Misunderstanding 3: Using a permanent chip allows the printer not to wash the head, saving ink

With the promotion of the CISS system, permanent chips for printer cartridges have also been adopted by many friends. Today's permanent chips generally have two functions: First, there is no need to decode. As long as the printer is turned off, the counter on the chip will be cleared to make the printer think that the ink in the ink cartridge is full. The second is to avoid nozzle cleaning, which means that the printer does not perform nozzle cleaning after power on, which can save some ink.

Because of these advantages of a permanent chip, many ordinary users who do not use a continuous-feed system also replace the chip on the ink cartridge with a permanent chip. However, because ordinary users have a small amount of daily printing, if the printer is not used for a long time, the ink in the nozzle must be increased in viscosity due to evaporation of water or dried up. This only depends on the automatic cleaning of the print head when the printer is turned on to solve the problem. After the permanent chip is installed, the printer will not clean the print head when the printer is turned on. Only when the user finds it abnormal after printing, the print head will be cleaned. This will not only save ink, but also cause more waste of printing paper and ink.

Of course, for a large-volume CISS system user, since a large amount of printing is required every day, the ink is not yet dried up and is brought out by the new ink, so that jamming is not likely to occur. However, many users have reported that the print quality has decreased after using the CISS system for a period of time. Some people thought that this was caused by aging of the print head or bad ink. However, when cleaning the print head of a printer using a continuous-feed system at a time, many nozzles were found during the inspection of the print head in the second consecutive article. The ink can be ejected, but the ejected ink is clearly bifurcated, and the print quality is increased after the nozzle is cleaned.

The reason for this is that there is something blocking the nozzle in the nozzle part. When the test page is printed, the nozzle can also eject part of the ink, so it is not easy to feel this blockage. However, this blockage will cause the ejected ink droplets to become smaller, so that the coverage of the ink droplets on the paper will be insufficient, and at the same time, the ejected ink will fly obliquely, and the positioning on the paper will be shifted, resulting in the printed image. The manuscript makes people feel coarse grained.

The cause of the partial nozzle clogging is that, with the use of a permanent chip, the printer does not have a certain relationship with the print head. The printer does not automatically clean the print head when using a permanent chip, and the user does not clean it because it does not feel blocked. In this way, impurities tend to adhere to the walls of the nozzle for a long period of time and become less easily cleaned. Waiting until the print is found to be poor can no longer bring out these impurities. Therefore, I suggest that when using permanent chips, it is best not to use chips that are free of nozzle cleaning.

Pantiliners herbal

 

Product features of pantiliners herbal

1. Ultra thin 1mm.

2. Softer than cotton, silky touch.

3. More than 700 penetration holes, super quick absorbent.

4. Ginseng herbal extracted by advanced technology provide 100% health care to women`s body.

5. 800 backsheet ventilation holes, moisture and odor controlled completely.

6. Perfect body fit and food grade adhesive keeps the pad stay on the panty firmly.

7. Individually aluminium wrapped.

 

Product functions of pantiliners herbal

1. Help improve immunity effectively.

2. Anti tumor effect.

3. Anti oxygenation effect, to make life longer.

4. Improve cardiac function.

5. Anti fatigue effect.

 

pantiliners herbal 

 

FAQ:

What is your Min. order quality?

A: One twenty-foot container, small quality available if has stock

 

Your supply ability?

A: 5,000,000 piece/pieces per week Sanitary Napkins in bulk

 

What is your neareast port?

A: Shenzhen

 

What is the payment terms you accepted?

A L/C, T/T, Western union, MoneyGram

Pantyliner Herbal

Pantyliner Herbal For Women,Pantyliner Herbal,Natural Pantyliner Herbal

Glory Power Hygiene Products Ltd. , https://www.hygienenapkin.com